Spark plugs
Published by Century Performance Center

Introduction:

The spark plug's location exposes it to extreme temperature variations, chemicals, fuels and oils. It is also attacked by cylinder pressures produced by the piston as well as cam timing, then it is also assaulted by high-output ignition units. As a result of all of this one can effectively learn what the engine is doing by reading the firing end of the spark plugs.

By careful examination of the plug's color, gap and any deposits that reside on it will show you the efficiencies as well as deficiencies of what is going on in the engine. Spark plugs should be checked at least yearly and replaces as often as necessary. In most cases you can follow the manufacturers recommendations, but in a race car, our replacement intervals are quite frequent.

How a Spark Plug Works:

The basic of a spark plug is that it must perform two primary functions.

1. To Ignite the Air/Fuel mixture
2. 2. To REMOVE the heat out of the combustion chamber

Spark plugs transmit electrical energy that turns fuel into working energy. A sufficient amount of voltage must be supplied by the ignition system to cause the spark to jump the across the spark plug gap, thus creating what is called Electrical Performance.

Additionally, the temperature of the spark plug's firing end must be kept low enough to prevent pre-ignition, but high enough to prevent fouling. This is called Thermal Performance and is determined by the heat range of the spark plug.

It is important to understand that spark plugs CANNOT create heat, only remove it! The spark plug works as a heat exchanger, pulling unwanted thermal energy away from the combustion chamber and transferring the heat to the engine's cooling system. The heat range is defined as a plug's ability to dissipate heat. The rate of heat is determined by:

• The insulator nose length
• Gas volume around the insulator nose
• Materials and/or construction of the center electrode and porcelain insulator

Now to the actual function. As the Ignition is triggered and sends the spark through the rotor, to the cap, down the wire and then it jumps the gap of the spark plug, a spark kernel is created that ignites the air/fuel mixture in the combustion chamber. Proper timing of this spark is not the only concern as described above. You must have the proper heat range (described later) as well as the correct gap.

On weaker or stock ignitions, opening up the gap CAN increase the spark kernel size, thereby creating a more efficient burn. The problem lies in that any added gap creates more strain on the other ignition parts.

• Coils may not have enough stored energy to fire, or in the least case, not enough energy to cross the gap, creating a miss-fire.
• Plug wires will break down due to the added resistance as the spark tries to reach ground
• Rotor and Cap, as well as points and the HEI carbon bushing will show early failures.

All of this is because the greater the gap, the higher the voltage requirement to jump the gap. Do not forget the gap of the rotor to the cap as well. A high performance rotor is a bit longer, allowing less spark loss or chance of spark scatter in the cap as the spark attempts to jump the plug gap. As many of us know that race, it is also possible to slow down a car if the gap is too big. I will get into this later when I describe proper plug gaps.

Heat Range:

A spark plug's heat range has no relationship on the actual voltage transferred through the spark plug. Rather, the heat range is a measure of the spark plug's ability to remove heat from the combustion chamber. The heat range measurement is determined by several factors:

• The length of the ceramic center insulator nose
• The insulator nose's ability to absorb and transfer combustion heat
• The material composition of the insulator
• The material composition of the center electrode

The longer the insulator nose, gives a larger surface area exposed to combustion gasses and heat is dissipated slowly. This also means the firing end heats up more quickly. We are talking about exposed ceramic length, not extended tip length.

The insulator nose length is the distance from the firing tip of the insulator to the point where the insulator meets the metal shell. Since the insulator tip is the hottest part of the spark plug, the tip temperature is a primary factor in pre-ignition and fouling. No matter what the plugs are installed in, be it a lawnmower, a boat, your daily driver or your race car, the spark plug tip temperature must remain between 450°C to 850°C. If the tip temperature is lower than 450°C, the insulator area surrounding the center electrode will not be hot enough to deter fouling and carbon deposit build-ups, thus causing misfires. If the tip temperature exceeds 850°C, the spark plug will overheat which can cause the ceramic around the center electrode to blister as well as the electrodes will begin to melt. This may lead to pre-ignition/detonation and expensive engine damage.

In identical spark plugs, the differences from one heat range to the next is the ability to remove approximately 70°C to 100°C from the combustion chamber. A projected style spark plug firing temperature is increased by 10°C to 20°C.

The firing end appearance also depends on the spark plug tip temperature. There are three basic diagnostic criteria for spark plugs: good, fouled, and overheated. The borderline between the fouling and optimum operating regions (450°C) is called the spark plug self-cleaning temperature. The temperature at this point is where the accumulated carbon and combustion deposits are burned off.

Bearing in mind that the insulator nose length is a determining factor in the heat range of a spark plug, the longer the insulator nose, the less heat is absorbed, and the further the heat must travel into the cylinder head water journals. This means that the plug has a higher internal temperature, and is said to be a "Hot" plug. A hot spark plug maintains a higher internal operating temperature to burn off oil and carbon deposits, and has no relationship to spark quality or intensity.

Conversely, a cold spark plug has a shorter insulator nose and absorbs more combustion chamber heat. This heat travels a shorter distance, and allows the plug to operate at a lower internal temperature. A colder heat range can be necessary when an engine is modified for performance, subjected to heavy loads, or it is run at high rpms for significant periods of time. The higher cylinder pressures developed by high compression, large camshafts, blowers and nitrous oxide, not to mention the rpm ranges we run our engines at while racing as make colder plugs mandatory to eliminate plug overheating and engine damage. The colder type plug removes heat more quickly, and will reduce the chance of pre-ignition/detonation and burn-out of the firing end. (Engine temperatures can affect the spark plug's operating temperature, but not the spark plug's heat range).

Influences on Spark Plug Temp and Performance:

Below is a list of possible external influences on a spark plug's operating temperatures. The following symptoms or conditions may have an affect on the actual temperature of the spark plug. The spark plug cannot create these conditions, but it must be able to deal with all the levels of heat, otherwise performance will suffer and engine damage can occur:

Air/Fuel Mixtures seriously affect engine performance and spark plug temps.

• Rich air/fuel mixtures cause tip temperature to drop, causing fouling and poor driveability.
• Lean air/fuel mixtures cause plug tip and cylinder temperatures to increase resulting in pre-ignition, detonation, and possibly serious spark plug and internal engine damage.
• It is important to read spark plugs many times during the tuning process to achieve optimum air/fuel mixture.

Higher Compression Ratios and Forced Induction will elevate spark plug tip and in-cylinder temperatures.

• Compression can be increased by performing any one of the following modifications:
• a) reducing combustion chamber volume (domed pistons, smaller chambers, milling heads, etc.)
• b) adding forced induction (Nitrous, Turbocharging, Supercharging)
• c) camshaft change
• As compression increases, a colder heat range plug is required, as well as higher octane fuel and paying careful attention to ignition timing and air/fuel ratios are also necessary.

Advanced Ignition Timing

Advancing timing by 10° causes plug temperature to increase by approximately 70°C to 100°C.

Engine Speed and Load

Increases in firing-end temperatures and are proportional to engine speed and load. When traveling at a constant high rate of speed, or hauling very heavy loads, a colder heat range spark plug should be installed.

Ambient Air Temperature:

• As air temperature falls, air density volume increases, resulting in leaner air/fuel mixtures. This creates higher cylinder pressures and temperatures that causes an increase in the spark plug's tip temperature. Fuel delivery should be increased.
• As temperature increases, air density decreases, as does intake volume, and fuel delivery should be decreased.

Humidity:

As humidity increases, air volume decreases. The result is lower combustion pressures and temperatures, causing a decrease in the spark plug's temperature and a reduction in available power. Air/Fuel mixture should be leaner, depending on ambient air temperature.

Barometric Pressure and Altitude

• Affects the spark plug's temperature
• The higher the altitude, the lower the cylinder pressure becomes. As the cylinder temperature decreases, so does the tip temperature
• Many tuners attempt to "chase" tuning by changing spark plug heat ranges.
• The real answer is to play with the jetting or air/fuel mixtures in an effort to put more air back in the engine.

Spark Plug Types and Designs:

There are hundreds of different spark plug types designed for different engines as well as specific applications. The two main ones we use in racing are the standard tip and extended tip. It is my opinion that any time you can use the extended tip, do it! The longer tip gets the spark kernel started further into the center of the bore for a more complete combustion process.

But, there are also specially designed spark plugs that are supposed to increase the spark kernel size. You see, the larger the spark kernel that is generated by the spark jumping the electrode gap, the more complete burn, the better power and efficiency and the smoother the car will run for longer periods of time. These specially designed plugs will have multiple angles that allow the spark to find the easiest path as well as getting the spark kernel out from under the ground electrode which can quench the kernel size limiting it's size and expansive growth.

Of these plugs, there are those that work, those that are hype, and those that are a great idea but they are manufactured by companies whose only purpose is profit instead of quality.

One thing to be wary of is plug material. Of the plugs I've tested, the fine-wire gold plugs have made the best power. The Platinum plugs are only good for longevity, though most imports run better with a platinum plug. This has to do with the material of the cylinder head and engine block and the plugs ability to properly ground.

People always ask my plug recommendations. I must say that I like the NGK V-Power Plugs, the Champion Premium Fine-Wire Gold plugs, and the Nippondenso U-Groove plugs for domestics. In the Imports, the Bosch or NGK Platinum plugs usually work best. I have been testing the AC RapidFire plugs currently and I must say I am impressed by the results. Plugs that are useless to me are the Split-Fire plugs (poor materials -- actually an Autolite plug with the "V" tip), and of course the Autolite plug itself. I have seen the most failures and poor performance out of these plugs. This is not a bash session, so those of you that love your Split-Fires or Autolites, I'll wait for you at the finish line.

Proper Plug Gapping:

Proper gapping of the spark plug is necessary to get maximum spark energy, lowest RFI release as well as what is best for the longevity of the secondary ignition components (coil, cap, rotor, wires, plugs).

When checking plug gaps, the correct way is to use ONLY wire gauges, though many of us are using the slider style gapping tools. These flat or feeler gauge style gauges do not accurately measure true width of spark plug gap.

When increasing the gap size for our high performance applications utilizing advanced ignition systems such as Mallory, Accel, Jacobs, Crane and Holley ... it is important never to go more than plus or minus .008". This is to maintain parallel surfaces between ground and the center electrodes.

Something many do not know, is that with Higher Compression ratios and Superchargers as well as Nitrous, in many cases smaller spark plug gaps must be used as well as the use of a much hotter ignition system. These higher cylinder pressures require more energy to jump the spark plug gap.

The rule of thumb on plug gaps is to open them up in .002" increments at a time. When the car (race vehicle) begins to lose power or slow down then go back .001-.002" and this in most cases is the optimum gap.

Remembering that the Ignition Unit, plug brand as well as heat range, cap and/or rotor styles and in many cases fuel type or brand will change the optimum spark plug gap settings. Lastly, NEVER use the porcelain insulator as a fulcrum point when setting these gaps either.